How to Wear Your Reviv (R1, R2 and R3): A Step-by-Step Guide

How to Wear Your Reviv (R1, R2 and R3): A Step-by-Step Guide

Open the box, rinse it, pop it in. That’s really all it takes. Your Reviv arrives ready to wear, so there’s nothing to boil, bite or mold. Here’s how to get started, and what the first few weeks usually feel like.

Step 1: Get the size right

A good fit starts with one number: the width across the outer edges of your upper back teeth. Age, gender and how an old guard felt don’t decide it. You can find yours with the bread test. 


Bite into a slice of bread, then measure the widest outer edges of the bite mark. Read it in millimetres, not centimetres. Prefer to watch? Our sizing video walks you through it: [sizing video link].

Model

Sizes

Notes

R1 (RevivOne)

Small, Large

Small starts at 45mm. Lightest and least bulky.

R2 (RevivTwo)

Medium, Large

Medium is 62mm and below. Large is 63mm and up.

R3 (RevivThree)

Medium, Large, XL

Medium 50-62mm. Large 63-72.4mm. XL 72.5mm and up.


Landing right on a boundary? Pick the size your number touches. And resist sizing up “for room”. A bigger guard usually feels worse, not better.

Step 2: Put it in

  1. Brush and floss, then give your Reviv a quick rinse in cool water.
  2. Place it in your mouth so it sits between your upper and lower teeth.
  3. Relax your jaw.
  4. Don’t wait for a tight grip. Reviv is loose by design, and that’s completely normal.



A few quick fixes. If the tongue tab digs in, trim it off. If the back ends make you gag, trim only those ends. And if your back molars don’t touch the guard, don’t worry. That’s common.

Step 3: Ease in, don’t rush

Think of the first two weeks as a warm-up, not a test. Here’s a typical pattern:

  • Days 1 to 3: 20 to 30 minutes in the daytime.
  • Days 4 to 7: build up to 2 or 3 hours.
  • Week 2: start wearing it overnight.

Reviv works in the day or at night. Your front and middle teeth take most of the contact, so a little early soreness is common. Does it slip out in the first days? Mouth tape and a few more short daytime sessions usually help.

Here’s a handy trick: keep a short journal for the first six weeks. Patterns show up faster than you’d think.

  • Keep it fresh
  • Every day: rinse in cool or lukewarm water. Clean gently with your fingers or a soft toothbrush, then air dry.
  • If it smells of the material: air it out, or soak it in diluted white vinegar (about 5%) for 30 to 60 minutes, then rinse well.

Optional: an ultrasonic cleaner like RePod cleans in a 3-minute cycle with just water.

Skip hot water, dishwashers, bleach and alcohol.



Store it smart

Let it dry fully, then keep it in a ventilated case somewhere cool and dry. Keep it away from direct sunlight, hot cars and curious pets.

Know when it’s time for a new one

Model

Typical lifespan

Guarantee

R1

2 to 4 months

None

R2

Varies with use

1 year replacement, one per customer account

R3

Varies with use

1 year replacement, one per customer account


The replacement guarantee covers genuine failure such as a rip, split or wear-through. It doesn’t cover loss or sizing. Replace your guard sooner if it tears, loses its shape or develops a smell or sticky texture that cleaning doesn’t fix.

Quick answers

Do I need to boil it?


No. R1, R2 and R3 are pre-formed, so there’s nothing to heat, bite or mold. Rinse it, place it in your mouth and you’re set. The only trimming you might do is the tongue tab or the back ends, and only if they bother you (see Step 2).

Which Reviv should I start with?


Most people start with the R3. It’s cut lower, has the biggest air holes and is the thickest between the teeth. The R2 has smaller air holes but the same firmness, the same height and the same one-year replacement guarantee. Neither is more durable than the other. The R1 is the lightest and least bulky, but it has a shorter lifespan and no guarantee. Compare all three here: [Reviv One vs Two vs Three].

Can I wear it in the day?


Yes. Reviv works in the day or at night, and building up with short daytime sessions is how we suggest you start. If you’d like a dedicated daytime option, our RevivDay guards (RD1 and RD2) are boil-and-mold, so they follow a different process from the R-series. Our guide walks you through them: [RD guide link].


Вернуться к блогу